Straight up: there is no single answer to "what should I buy," because the right answer depends almost entirely on what the part is doing. I'm the office administrator for a 90-person company. I manage roughly $180,000 a year in MRO and facility spend across 11 vendors, and I report to both operations and finance. Half my requisitions are overhead lifting gear. The other half are things like a 2-pack of 8 x 32 brass wood insert nuts or a box of slotted-drive machine screws.
Same purchase order system. Completely different rules. So I stopped hunting for one universal policy and started sorting every request into three buckets.
The Three Questions That Sort the Job
Before I look at price or brand, I ask three things:
- Does anything go overhead? If a person or anything valuable will be under the load, this is a lifting application. Different rules apply, and they are not flexible.
- Is the part structural, or is it holding a faceplate on? Nobody stands under a cabinet door.
- Do we fabricate it, or do we buy the finished part? This is where the hole saw question lives.
Answer those three and the right purchase kind of falls out on its own. Here's how each bucket works in practice.
Scenario 1: The Load Goes Overhead
Let me be clear about my limits. I'm not a rigger. I buy the hardware; the rigging plan belongs to someone qualified. But I've learned enough to know this is the one bucket where "find the lowest quote" is the wrong instinct.
What certification actually buys you
A Crosby shackle costs more than a no-name shackle of the same size. The difference isn't some exotic alloy. It's documentation and traceability: a rated working load limit marked on the body, a manufacturer's identification, and a paper trail that survives an audit or, worse, an incident.
Per ASME B30.26, rigging hardware such as shackles, hooks, rings, and links must be marked with its rated load and identified to the manufacturer. Verify current requirements at asme.org, and check your own jurisdiction's rules.
I'm not saying anything unmarked is junk. I'm saying I can't prove what it is, and in a lift application, being able to prove it is the job.
Cost context, as of January 2025: a 3/4-ton screw pin anchor shackle runs roughly $18–35 depending on size and seller. A generic import of similar size might be $6. That $20–30 gap is not where I try to save money. Verify current pricing before you budget.
The mismatch trap
Here's the genuinely counterintuitive part: buying a stronger shackle than the rest of the rig gains you nothing. A rig fails at its weakest link. A 3-1/2 ton shackle on a 1-ton sling just means you paid more for the same outcome. Match the components — shackle to sling to hook — so the assembly is rated to the load, not the parts individually.
Two things I've internalized the hard way. Never replace a shackle pin with a bolt. Never heat, weld, or bend a shackle to make it fit. Both are covered in Crosby's user guide, and both are the kind of shortcut someone in the shop thinks is clever at 3 p.m. on a Friday.
If the rig uses webbing rather than chain or wire, a web sling shackle has a wider bow so flat webbing isn't pinched against a sharp edge. That's the "crosby web sling shackles" request I get from our shop lead at least twice a year, and it's a legitimately different part — not a substitute.
Weighing the risk out loud
The upside of cheaper shackles on a 1-ton lift was maybe $60 across four units. The risk was a dropped load. I ran that trade in my head once, decided the math wasn't close, and stopped shopping this category on price. That was the whole decision. No spreadsheet.
Two references worth knowing: OSHA 29 CFR 1910.184 covers slings in general industry, and 1926.251 covers rigging equipment for material handling in construction. Verify current wording at osha.gov — don't take my summary as compliance advice.
Scenario 2: It Holds Something Up But Nobody Stands Under It
Now the other half of my orders. Cabinet doors. Display case hinges. A stripped screw hole in a conference table. Fasteners, not rigging.
8 x 32 brass wood insert nuts and the 2-pack math
A brass wood insert nut with an 8-32 internal thread is a repair part. Its job: give a machine screw something threaded to bite into when the original wood threads have stripped out. The "8 x 32" is the thread — #8 screw, 32 threads per inch, UNC. The brass is there for corrosion resistance and appearance, not strength.
Counterintuitive take: for a one-off fix, buying the 2-pack at $4–9 is usually correct even though the per-unit price is terrible. I have a 100-count box of a slightly wrong diameter sitting in a bin because I "saved money" buying bulk for a job I will never do again. The 2-pack ships today and actually fits.
Brass is soft. Over-torque it and the slotted drive or the internal threads deform. Check the maker's pilot-hole chart for the material you're inserting into — wrong pilot diameter is the number one reason these things spin instead of set. A little wax or soap on the threads helps more than you'd think.
Slotted-drive machine screws
Slotted drive is what you need when you're matching vintage hardware or a faceplate that already has slotted screws. Here's the thing most people miss: the driver matters more than the screw. A slotted screw engages on two points, so a tapered or worn screwdriver cams out and scars the brass. Use a hollow-ground cabinet screwdriver that actually matches the slot width. That single tool purchase has saved more faceplates than any product choice I've made.
Material matching matters too. Brass screw into a brass insert is a galling risk; stainless into aluminum seizes more often than people expect. For indoor use, zinc-plated steel or brass screws at roughly $8–15 per hundred (as of January 2025) are fine.
And the second counterintuitive one: spending triple on 18-8 stainless here is usually wasted money. You're buying corrosion resistance for a cabinet that never gets wet. Premium is not the default answer — value is. That's a different thing.
Scenario 3: You Need a Hole in Metal
Can a hole saw cut through metal? Yes — with conditions
This is the most-asked question from our shop, so, short answer: yes. A bi-metal hole saw will cut mild steel sheet and thinner plate. But it's a conditional yes, and the conditions are exactly where people burn through saws and drill motors.
- Bi-metal saws for mild steel and thinner stock. Carbide-tipped or carbide-grit for stainless, cast iron, or heavier plate.
- Low RPM, steady feed. High speed glazes the teeth and work-hardens stainless — the saw slicks over instead of cutting.
- Cutting fluid. No exceptions on steel. It's the cheapest thing you'll buy for this job.
- Center punch first. The pilot bit drills before the saw touches anything, and it can walk.
- Know the no's: hardened steel, thick plate with a standard saw, or any cut where your saw's depth is less than your material thickness.
Honestly, I've never fully understood why two people with identical setups get different results. My best guess is feed-pressure and RPM discipline — hand feel, not the tool. If someone has a better explanation, I'd genuinely like to hear it.
When to pay someone else to drill it
This one took me a while. For a single hole, the cheapest option is often a machine shop. A decent carbide-tipped saw is $30–60, and a $60 drill motor is not built for that kind of load — I've seen one die mid-cut. A shop with a punch or a waterjet will do one hole for roughly $30–60 (based on quotes I collected in Q4 2024; verify locally), to tighter tolerance, while you do something else.
Also worth knowing: for thin sheet and electrical panels, knockout punches and step drills beat hole saws outright. No pilot bit, no walking, no chatter.
Simple rule: one hole, pay someone. A pattern of identical holes, buy the tool. The crossover in my experience is around five or six holes in the same size.
How to Tell Which Scenario You're In
Practical checklist, in order:
- Anything overhead? You're in Scenario 1. Certified, marked hardware with a stated working load limit. Components matched to each other. A qualified rigger signs the plan, not the purchasing department.
- No overhead load, small repair? Scenario 2. Buy the small pack, match the materials, buy the correct driver, and don't pay for corrosion resistance nobody will ever need.
- Cutting or shaping metal? Scenario 3. Count the holes first. One hole, outsource it. Many, buy the right blade for the material.
The ambiguity trap is the middle of the shop — a bracket, a link, an eyebolt, anything that could end up in a lift someday. If there's any chance, treat it as Scenario 1. The cost of over-buying is a few dollars. The cost of under-buying isn't symmetric, and I've watched someone explain that difference to a safety officer. Not fun.
I hit order confirm on the last batch of shackles and immediately started second-guessing whether I'd sized them right against the slings. Didn't relax until the rigger signed off on the assembly. That's normal for this category.
Bottom line: the lowest quote has cost us more in about 60% of cases I can actually count — usually through rework, a second order, or a part that didn't fit. Value beats price every time the part matters. But "value" doesn't always mean premium. Sometimes it means a $6 2-pack and a $12 screwdriver.
Pricing in this article is general reference only, based on quotes and retail listings accessed January 2025. Actual prices vary by vendor, specification, size, and date of order — verify current rates before purchasing. Regulatory references are for general guidance; consult official sources and a qualified person for current requirements.
Leave a Reply